Installation, Operation, and Maintenance Manual
You can download your own copy of the most up-to-date IOM Manual below.
- Installation, Operation, and Maintenance Manual
- SAFE-Tank® and Bellows Transition Fitting Installation Videos
- IMFO® Fitting Installation [Videos]
- Reverse Float Level Gauge [Video]
- Insulation [Video]
- Standard fittings [Video]
Installation, Operation, and Maintenance Manual
| Revision Date | Revision Items |
|---|---|
| 8-24 | General updates to Table of Contents and page organization |
| 5-28-24 | Changed the bolt hole sizes for the B.O.S.S. fitting and the Stainless Steel fittings. Changed from 9/16″ to 5/8″ |
| 5-24 | Added, “Make sure the IMFO neck is supported and the maximum concrete pad projection is 2” under the IMFO neck. (See pictures below) Make sure there are no valves or heavy piping hanging off the IMFO.” to page 3. |
| 4-2024 | Fixed page numbering issues. |
| 3-2024 | All new reformatted IOM Manual. |
| 9-8-23 | Updated offloading instructions regarding foamed tanks and wooden cradles. |
| 8-2-23 | Clarified that seismic systems are different in many cases. Added “The material, type of clip, quantity of clips, cables, etc. may vary. Please consult the calculations that were sent with your system or contact Poly Processing with any questions.” It is critical to reference the calculations for your specific seismic system and tank. |
| 6/2023 | Added a link on page 40. |
| 10/2022 | Added verbiage regarding Enhanced Bellows Transition Fitting – Make sure all all bolts of the piping assembly are properly torqued including the primary tank fitting, expansion joint connections, and the threaded coupler if a B.O.S.S. fitting is installed. Go to www.polyprocessing.com/safetankinstall for SAFE-Tank installation videos. |
| 8/2022 | Added links to more IOM information on Page 40 |
| 2/2022 | Updated cover and links to Installation, Operation, and Maintenance Manual |
| 9/2021 | Added notes section on back page |
| 6/2021 | Updated RFLG page |
| 3/2021 | Included new SAFE-Tank and Transition fitting instructions and landing page link |
| 11/2020 | Updated Bellows Transition Fitting Installation instructions and added polyprocessing.com/safetankinstall for SAFE-Tank Installation Instructions page with video installation instructions. |
| 10/2020 | Added text on page 23 regarding the need for a crane or boom truck to set the transition fitting in place. Set the transition fitting before the crane or boom truck leaves the installation |
| 09/2020 | Added note regarding flexible connectors |
| 08/2020 | Updated IMFO base information. Updated flexible connection section with EPDM expansion joints and updated guidelines |
| 07/10/2020 | Updated reference page numbers for flexible connections and piping support |
| 05/20/2020 | Updated seismic drawings and instructions |
| 03/03/2020 | Added verbiage regarding butterfly valve installation |
| 02/13/2020 | Added : Reverse Float system may not include internal downpipe and pipe support if ordered without it. Check with your sales contact to see if it was included in the order |
| 07/30/2019 | Updated the Bellows Transition Fitting instructions |
| 12/01/2018 | Added link to PPC IOM Manual on front cover |
| 11/06/2017 | Added “Venting charts based on recommendation and criteria from Venting Design for ACFM Technical Paper”, page 4 |
| 10/01/2017 | Added current revision date on all pages |
| 7/01/2017 | Added new Bellows Transition Fitting installation information, pages 22-24 |
| 6/05/2017 | Added IMFO support information, pages 3 & 10 |
| 6/01/2017 | Corrected ladders pages |
| 5/01/2017 | Added calibration tape instructions, page 18 |
If you need additional assistance or have a question about installation, please contact customer support.
